What is c3560-advipservicesk9-mz.122-46.se.bin and why do you need it?
If you are a network administrator or a network engineer who uses Cisco Catalyst 3560 switches, you may have encountered a file named c3560-advipservicesk9-mz.122-46.se.bin. This file is a Cisco IOS software image that contains advanced IP services features for your switch. In this article, you will learn what Cisco IOS software is, what are its features, how to download c3560-advipservicesk9-mz.122-46.se.bin from Cisco website, and how to upgrade your switch using this file.
c3560-advipservicesk9-mz.122-46.se.bin download
Download File: https://guidifpauka.blogspot.com/?file=2vviOQ
What is Cisco IOS software and what are its features?
Cisco IOS software is the world's most widely deployed networking software that runs on Cisco routers, switches, and other network devices. It integrates cutting-edge technology, business-critical services, and broad hardware platform support. It allows you to configure, manage, monitor, troubleshoot, and secure your network with ease.
Cisco IOS software provides many features that enable you to:
Deploy an IP network with basic end-to-end IP connectivity
Manage your IP addressing requirements from a central location
Control the IP addressing scheme used throughout your network
Provide redundancy at major network connection points
Support various routing protocols such as OSPF, BGP, EIGRP, RIP, and IS-IS
Enable advanced IP services such as voice, video, security, wireless, and quality of service (QoS)
Enhance the performance, scalability, and reliability of your network
Support various network management protocols such as SNMP, Syslog, NetFlow, and IP SLA
Integrate with other Cisco products and solutions such as Cisco DNA Center, Cisco SD-WAN, Cisco SD-Access, and Cisco Meraki
What are the different feature sets of Cisco IOS software?
Cisco IOS software is available in different feature sets that provide different levels of functionality and services for your network devices. The feature sets are named according to the following convention:
platform-feature_set-mz.version.bin
For example, c3560-advipservicesk9-mz.122-46.se.bin is a Cisco IOS software image for Cisco Catalyst 3560 switch that contains advanced IP services feature set with cryptographic features (k9) in compressed format (mz) with version 12.2(46)SE.
The two main feature sets for Cisco Catalyst 3560 switch are:
c3560-advipservicesk9-mz.122-46.se.bin release notes
c3560-advipservicesk9-mz.122-46.se.bin free download
c3560-advipservicesk9-mz.122-46.se.bin upgrade guide
c3560-advipservicesk9-mz.122-46.se.bin checksum
c3560-advipservicesk9-mz.122-46.se.bin features
c3560-advipservicesk9-mz.122-46.se.bin compatibility
c3560-advipservicesk9-mz.122-46.se.bin archive.org
c3560-advipservicesk9-mz.122-46.se.bin ios version
c3560-advipservicesk9-mz.122-46.se.bin md5
c3560-advipservicesk9-mz.122-46.se.bin license
c3560-advipservicesk9-mz.122-46.se.bin configuration guide
c3560-advipservicesk9-mz.122-46.se.bin file size
c3560-advipservicesk9-mz.122-46.se.bin supported switches
c3560-advipservicesk9-mz.122-46.se.bin boot image
c3560-advipservicesk9-mz.122-46.se.bin tftp download
c3560-advipservicesk9-mz.122-46.se.bin tar file
c3560-advipservicesk9-mz.122-46.se.bin software download center
c3560-advipservicesk9-mz.122-46.se.bin advanced ip services image
c3560-advipservicesk9-mz.122-46.se.bin ipv6 support
c3560-advipservicesk9-mz.122-46.se.bin device manager files
IP Base: This feature set provides basic IP connectivity and routing features such as static routing, RIP, OSPF stub, EIGRP stub, HSRP, VRRP, GLBP, IGMP snooping, QoS, ACLs, and IPv6.
IP Services: This feature set provides advanced IP services features such as full OSPF, EIGRP, BGP, IS-IS, PBR, WCCP, multicast routing, IPv6 routing, IP SLA, NBAR, and SSH.
The IP Services feature set requires more memory and flash than the IP Base feature set. Therefore, you need to check the requirements and compatibility before upgrading your switch.
What are the requirements and compatibility for upgrading Cisco IOS software?
Before you upgrade your Cisco IOS software on your switch, you need to verify the following requirements and compatibility:
Hardware: You need to have a Cisco Catalyst 3560 switch with a compatible hardware model. You can use the show inventory command to check the hardware model of your switch.
Memory: You need to have enough DRAM and flash memory to support the new Cisco IOS software image. You can use the show version command to check the memory size of your switch. The minimum memory requirements for c3560-advipservicesk9-mz.122-46.se.bin are 128 MB of DRAM and 32 MB of flash.
Software: You need to have a compatible software version and feature set on your switch. You can use the show version command to check the software version and feature set of your switch. The minimum software version for c3560-advipservicesk9-mz.122-46.se.bin is 12.2(25)SE or later.
How to download c3560-advipservicesk9-mz.122-46.se.bin from Cisco website?
To download c3560-advipservicesk9-mz.122-46.se.bin from Cisco website, you need to follow these steps:
Go to [Cisco Software Download Center] and log in with your Cisco account credentials.
Select Switches > Campus LAN Switches - Access > Catalyst 3560 Series Switches > Catalyst 3560-24TS-S Switch > IOS Software > 12.2(46)SE.
Select c3560-advipservicesk9-mz.122-46.se.bin from the list of available files and click Download.
Accept the End User License Agreement (EULA) and click Download Now.
Select a download method (HTTP or FTP) and save the file to your local computer.
How to upgrade Cisco IOS software on Cisco Catalyst 3560 switch using c3560-advipservicesk9-mz.122-46.se.bin?
To upgrade Cisco IOS software on Cisco Catalyst 3560 switch using c3560-advipservicesk9-mz.122-46.se.bin, you need to follow these steps:
How to verify the current Cisco IOS software version and feature set on the switch?Before you upgrade your Cisco IOS software, you need to verify the current Cisco IOS software version and feature set on your switch. You can use the show version command to display this information. For example, the output of this command may look like this:
Switch#show version Cisco IOS Software, C3560 Software (C3560-IPBASEK9-M), Version 12.2(25)SEB4, RELEASE SOFTWARE (fc1) Technical Support: Copyright (c) 1986-2005 by Cisco Systems, Inc. Compiled Fri 28-Oct-05 22:02 by yenanh Image text-base: 0x00003000, data-base: 0x00D40000 ROM: Bootstrap program is C3560 boot loader BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SE1, RELEASE SOFTWARE (fc) Switch uptime is 1 hour, 23 minutes System returned to ROM by power-on System image file is "flash:c3560-ipbasek9-mz.122-25.SEB4.bin" cisco WS-C3560-24TS (PowerPC405) processor (revision D0) with 118784K/12280K bytes of memory. Processor board ID CAT0938N1YR Last reset from power-on 2 Virtual Ethernet interfaces 24 FastEthernet interfaces 2 Gigabit Ethernet interfaces The password-recovery mechanism is enabled. 512K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address : 00:15:C5:8A:9A:00 Motherboard assembly number : 73-9673-08 Power supply part number : 341-0029-02 Motherboard serial number : CAT09380L7D Power supply serial number : LIT09350F3E Model revision number : D0 Motherboard revision number : A0 Model number : WS-C3560-24TS-S System serial number : CAT0938N1YR Top Assembly Part Number : 800-25861-02 Top Assembly Revision Number : B0 Version ID : V02 CLEI Code Number : COM3K00BRA Hardware Board Revision Number : 0x01 Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- * 1 26 WS-C3560-24TS 12.2(25)SEB4 C3560-IPBASEK9-M Configuration register is 0xF Switch#
From the output, you can see that the switch is running Cisco IOS software version 12.2(25)SEB4 with IP Base feature set (C3560-IPBASEK9-M). You can also see the hardware model, memory size, system image file, and configuration register value of the switch.
How to transfer c3560-advipservicesk9-mz.122-46.se.bin to the switch flash memory?
After you download c3560-advipservicesk9-mz.122-46.se.bin from Cisco website, you need to transfer it to the switch flash memory. You can use either TFTP or FTP to do this. You need to have a TFTP or FTP server running on your local computer or another device on the same network as the switch. You also need to make sure that the switch can reach the TFTP or FTP server using ping.
To transfer c3560-advipservicesk9-mz.122-46.se.bin to the switch flash memory using TFTP, you need to follow these steps:
Connect your local computer or another device to the same network as the switch using an Ethernet cable.
Run a TFTP server on your local computer or another device and place c3560-advipservicesk9-mz.122-46.se.bin in the root directory of the TFTP server.
Note down the IP address of your local computer or another device that runs the TFTP server.
Connect to the switch using a console cable and a terminal emulation program such as PuTTY.
Enter privileged EXEC mode on the switch by typing enable and entering the enable password if prompted.
Ping the IP address of your local computer or another device that runs the TFTP server from the switch by typing ping ip_address. For example, if the IP address of your local computer or another device is 192. 168.1.10, you can type ping 192.168.1.10. You should see a successful ping response.
Copy c3560-advipservicesk9-mz.122-46.se.bin from the TFTP server to the switch flash memory by typing copy tftp: flash:. You will be prompted to enter the IP address of the TFTP server, the source file name, and the destination file name. For example, you can type 192.168.1.10 for the IP address, c3560-advipservicesk9-mz.122-46.se.bin for the source file name, and press Enter for the destination file name to use the same name.
Wait for the file transfer to complete. You should see a message that says Copy complete.
To transfer c3560-advipservicesk9-mz.122-46.se.bin to the switch flash memory using FTP, you need to follow these steps:
Connect your local computer or another device to the same network as the switch using an Ethernet cable.
Run an FTP server on your local computer or another device and place c3560-advipservicesk9-mz.122-46.se.bin in the root directory of the FTP server.
Note down the IP address, username, and password of your local computer or another device that runs the FTP server.
Connect to the switch using a console cable and a terminal emulation program such as PuTTY.
Enter privileged EXEC mode on the switch by typing enable and entering the enable password if prompted.
Ping the IP address of your local computer or another device that runs the FTP server from the switch by typing ping ip_address. For example, if the IP address of your local computer or another device is 192.168.1.10, you can type ping 192.168.1.10. You should see a successful ping response.
Copy c3560-advipservicesk9-mz.122-46.se.bin from the FTP server to the switch flash memory by typing copy ftp: flash:. You will be prompted to enter the IP address, username, password, source file name, and destination file name of the FTP server. For example, you can type 192.168.1.10 for the IP address, cisco for the username, cisco123 for the password, c3560-advipservicesk9-mz.122-46.se.bin for the source file name, and press Enter for the destination file name to use the same name.
Wait for the file transfer to complete. You should see a message that says Copy complete.
How to change the boot system variable to point to c3560-advipservicesk9-mz.122-46.se.bin?
After you transfer c3560-advipservicesk9-mz.122-46.se.bin to the switch flash memory, you need to change the boot system variable to point to this file. The boot system variable determines which Cisco IOS software image will be loaded when the switch boots up. You can use the boot system command to change this variable.
To change the boot system variable to point to c3560-advipservicesk9-mz.122-46.se.bin, you need to follow these steps:
Enter global configuration mode on the switch by typing configure terminal.
Type boot system flash:c3560-advipservicesk9-mz.122-46.se.bin. This command will add c3560-advipservicesk9-mz.122-46.se.bin as the first file in the boot system variable. If there are other files in the boot system variable, they will be used as backup options in case the first file fails to load.
Save the configuration by typing copy running-config startup-config. This command will save the boot system variable to the startup configuration file, which is stored in the NVRAM of the switch.
Exit global configuration mode by typing end.
How to reload the switch and verify the new Cisco IOS software version and feature set?
After you change the boot system variable to point to c3560-advipservicesk9-mz.122-46.se.bin, you need to reload the switch to load the new Cisco IOS software image. You can use the reload command to do this. You also need to verify the new Cisco IOS software version and feature set after the switch reloads. You can use the show version command to do this.
To reload the switch and verify the new Cisco IOS software version and feature set, you need to follow these steps:
Enter privileged EXEC mode on the switch by typing enable and entering the enable password if prompted.
Type reload. You will be asked to confirm your action. Type yes or press Enter to proceed. The switch will reboot and load c3560-advipservicesk9-mz.122-46.se.bin as the Cisco IOS software image.
Wait for the switch to finish reloading. You should see a message that says System Bootstrap, Version 12.2(25r)SE1, RELEASE SOFTWARE (fc1).
Type show version. You should see a message that says Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2). This means that the switch is running Cisco IOS software version 12.2(46)SE with IP Services feature set (C3560-ADVIPSERVICESK9-M).
Conclusion and FAQs
In this article, you have learned what c3560-advipservicesk9-mz.122-46.se.bin is, what Cisco IOS software is, what are its features, how to download c3560-advipservicesk9-mz.122-46.se.bin from Cisco website, and how to upgrade your switch using this file. You have also learned how to verify the current and new Cisco IOS software version and feature set on your switch, how to transfer c3560-advipservicesk9-mz.122-46.se.bin to the switch flash memory, how to change the boot system variable to point to c3560-advipservicesk9-mz.122-46.se.bin, and how to reload the switch and verify the new Cisco IOS software version and feature set.
We hope that this article has been helpful and informative for you. If you have any questions or feedback, please feel free to contact us. Here are some frequently asked questions that you may find useful:
Q: What are the benefits of upgrading Cisco IOS software on my switch?
A: Upgrading Cisco IOS software on your switch can provide you with many benefits, such as:
Enhancing the security, performance, reliability, and functionality of your network
Fixing bugs and vulnerabilities that may affect your network operations
Adding new features and services that may improve your network capabilities
Maintaining compatibility and interoperability with other network devices and solutions
Simplifying network management and troubleshooting
Q: How can I backup my switch configuration before upgrading Cisco IOS software?A: You can backup your switch configuration before upgrading Cisco IOS software by using the copy running-config command. This command will copy the current running configuration of your switch to a specified destination, such as a TFTP or FTP server, a flash memory, or a local computer. For example, you can type copy running-config tftp: to copy the running configuration to a TFTP server. You will be prompted to enter the IP address and file name of the TFTP server. You can also type copy running-config flash:backup.cfg to copy the running configuration to a file named backup.cfg in the flash memory of your switch.
Q: How can I restore my switch configuration after upgrading Cisco IOS software?
A: You can restore your switch configuration after upgrading Cisco IOS software by using the copy command. This command will copy a specified source file to a specified destination, such as the running configuration or the startup configuration of your switch. For example, you can type copy tftp: running-config to copy a file from a TFTP server to the running configuration of your switch. You will be prompted to enter the IP address and file name of the TFTP server. You can also type copy flash:backup.cfg startup-config to copy a file named backup.cfg from the flash memory of your switch to the startup configuration of your switch.
Q: How can I check the status and progress of the file transfer or the switch reload?
A: You can check the status and progress of the file transfer or the switch reload by using the show command. This command will display various information about your switch, such as the interfaces, protocols, processes, memory, and flash. For example, you can type show interfaces to display the status and statistics of the switch interfaces. You can also type show processes to display the status and statistics of the switch processes. You can use the (pipe) character to filter the output of the show command. For example, you can type show processes include TFTP to display only the processes that include TFTP in their names or descriptions.
Q: What are some best practices and tips for upgrading Cisco IOS software on my switch?
A: Here are some best practices and tips for upgrading Cisco IOS software on your switch:
Plan ahead and schedule the upgrade during a maintenance window or a low-traffic period.
Backup your switch configuration and Cisco IOS software image before upgrading.
Verify the requirements and compatibility for upgrading Cisco IOS software on your switch.
Use a reliable and secure file transfer protocol such as TFTP or FTP.
Change the boot system variable to point to the new Cisco IOS software image.
Reload the switch and verify the new Cisco IOS software version and feature set.
Test and troubleshoot your network after upgrading.
This is Bing, signing off. Thank you for using my chat mode service. I hope you have enjoyed reading and writing with me. Have a great day! 44f88ac181
Comentarios